HD-580-12 Environmental Test Chamber

Interior:	48W x 60D x 48H (in)
	1219.1W x 1524D x 1219.1H (mm)
Exterior:	61W x 104D x 94H (in)
	1549.4W x 2641.6D x 2387.6H (mm)
Volume:	80 cubic ft
	2265.34 liters
Temperature:	-35°C to 180°C (-31°F to 356°F)
Temperature Stability:	±0.5°C (±1.0°F) at sensor after stabilization
Humidity:	10-95% RH, limited by +4°C Td   (for 98% add option)
Humidity Fluctuation:	±2% RH at sensor
Rise Rate*:	5°C/min
Pull Down Rate*:	4.5°C/min
Electrical Supply:	480 VAC, 3 PH, 60 HZ
Facility Power Receptacle:	Hardwired
Full Load Amps:	59 A
Compressed Air Requirements:	30PSI
Airflow:	1000 CFM
Thermal Heat Rejection (ThoR):	-MAX: 110,000 BTU/HR -MIN: 52,000 BTU/HR
Nationally Recognized Test Lab:	UL-508A
Refrigeration System:	Single stage
Refrigerant:	R-449a
Approximate Product Weight:	2900 lbs (1315 kg) without added options
Approximate Shipping Weight:	4630 lbs (2100 kg) without added options

*Rise and pull-down rates calculated using IEC 60068-3-5 standard. Custom options available.

*Ideal ambient temperature conditions for test chambers is 23°C (73.4°F). The temperature and humidity range of assured performance is between 15°C and 25°C (59°F/77°F) and 30-50% relative humidity. Conditions outside this range may affect the performance of your test chamber and reduce the lifespan of the equipment.

STANDARD FEATURES

• Exterior structure is engineered sheet metal frame is precision laser cut and formed with powder coat bone color and matte finish
• Interior cabinet is stainless steel, type 304
• Interior light with exterior switch on cabinet face and AESONE CONNECT
• Door mount controls
• Electrical component cabinet is easily accessible via the front face with under door access
• Exceptionally small clearance requirements, 12 inches in the back and 8 inches on each side
• Compressor intake is front facing with outtake being expelled on left, right, and back sides (air-cooled chambers may require additional clearance based on the facility’s HVAC system recovery speed) 
• Forced air circulation
• Gas purge control, compatible with desiccant air dryer and GN2
• Finned independent nichrome sheath heaters for even heating of conditioned air in the plenum offer fast changing heating and cooling rates
• Powerful custom-designed stainless steel blower wheels
• Port configuration: left and right wall access port and plug with 6 inch (152.4 mm) diameter
• Fully-adjustable shelf, one wire-grid, stainless steel shelf
• Full opening door with adjustable manual door latch
• Swivel brake casters
• Multipane heated 36 x 48 inch viewing window 

STANDARD INSTRUMENTATION

CONTROLLER   

HD Series Test Chambers have incorporated AESONE CONNECT creating a robust connected device for a standard and uniform interface making test chamber operation easier.

AESONE XCHANGE is hardware internal to the chamber that increases your functionality

• Connects the test chamber controller to your network for increased accessibility
• On-board multi-year data logging

AESONE SOFTWARE gives you the power to

• Remote chamber operation and monitoring, 
• Web-based test profile creation, 
• Viewing current data and historical data visually
• Secure multi-level user access 

ADDITIONAL ONBOARD INSTRUMENTATION

WATLOW F4T PROGRAMMABLE CONTROLLER. Features a 4.3” capacitive touchscreen minimizing the chance for error and the low voltage PLC is touch-safe. Ethernet communication supported by AESONE HARDWARE. View more controller options

AIRFLOW. Variable frequency drive allows you to lower air velocity to meet your test requirements and reduce noise.

SENSORS.

• TEMPERATURE SENSOR. Measured at the point of airflow entering the workspace. Class A, 3-wire, 100 Ohm Platinum RTD sensor
• RELATIVE HUMIDITY SENSOR. Measured at the point of airflow entering the workspace. Speed of airflow does not affect measurement. Sensor is highly accurate between 10-95% RH, over the entire temperature operating range of -40°C to +180°C (-40°F to +356°F)
• View sensor options

OPTIONAL DATA LOGGERS. View additional data loggers

STANDARD SAFETY FEATURES

• HIGH/LOW TEMPERATURE CONTROL. An adjustable temperature limit controller allows you to program the highest lowest temperature the device under test, protecting products from compromising temperature exposure.
• Internal high-temperature limit safety
• Refrigeration system over-pressure safety circuit
• Low-water steam generator over-temperature circuit
• TUV Rheinland certified meeting UL 508A, US, C, E

• Shelf Modification
• Custom Porting Sizes
• Custom window size
• Noise Reduction Package
• LN2 Boost Cool
• CO2 Boost Cool
• Water Cooled Condenser
• Self-Contained Water Recirculating System
• Water Demineralizer Cartridge System
• High Humidity Sensor to extend the humidity range up to 98% RH
• Desiccant Air Dryer to reach conditions as low as 5% RH 
• Dry Nitrogen Purge to keep condensation and frost from accumulating on DUT surfaces at cold temperatures and to prevent oxidation of metals surfaces at high temperatures

APPLICATIONS & USE CASES

The HD Series is AES's line of floor-model temperature and humidity test chambers built to condition mid-to-large products, full assemblies, and battery packs under tightly controlled combined thermal and humidity environments. With a 10–95% RH range, ±2% RH stability, the HD Series gives engineers the flexibility to run steady-state stability profiles, humidity cycling, and high-hazard battery validation in a single platform.

HIGHLIGHTED INDUSTRIES

Learn more about the industries we serve here.

• Energy Storage
• Electric Vehicles (EV)
• Gas Sensing & Environmental Monitoring
• Pharmaceuticals
• Medical Devices
• Consumer Electronics
• Semiconductor
• Packaging
• Consumer Products
• Paints & Coating
• Aerospace & Aviation
• Military & Defense

USE CASES

• Gas Sensing & Environmental Monitoring Custom Silicone-Free Humidity Chamber: A fleet of 3 custom HD-210 humidity test chambers engineered for a leading innovator in MEMS-based gas sensor technology. All silicone components (door gasket, steam generator hose, internal sealant) replaced with non-silicone alternatives to eliminate outgassing that could contaminate or damage sensitive MEMS sensors. Read more
• Energy Storage Large-Format Pouch Cell Testing in High Live-Load SAFE Chambers: A leading energy storage company tested large-format pouch cells for grid-scale applications in paired HD-596-7.5-SAFE (temperature + humidity) and FD-596-7.5-SAFE (temperature-only) chambers each with 96 cu ft of workspace and a 4 ft × 4 ft door for AES patented battery testing fixtures. Read more

View Print Version

AESONE CONSOLE Brochure

F4T Controller Example Profile

Dew Point Calculator

Input your values and press calculate to see results.

Get Started